Automotive Repair Tools › otc 1932 3 4 drive

OTC SOC 4-7/8 3/4D LCKNT 6PT DP SATIN

Features and Benefits: 4-7/8 6 point locknut socket Wheel bearing locknuts are easy to remove or install with these specially designed sockets Sockets are made of high-strength steel; openings resist rounding out Can be used with an extension and... more

OTC SOC 3-1/8 3/4D LCKNT 8PT DP SATIN

Features and Benefits: This high grade truck wheel bearing locknut is made of high strength steel Socket is designed for use with 3/4 square-drive manual tool only Opening size: 3-1/8 A long extension may be attached to the socket to provide the... more

OTC PULLER 3 JAW ADJUSTABLE 3-1/2IN. 1TON

Features and Benefits: This 3 jaw puller has a 1 ton capacity Maximum reach of 2-1/8 and the maximum spread of 3-1/4 Screw size 5/16 - 24 x 3-7/8 Jaw thickness 9/64 Jaw width 1/4 These pullers are forged from quality steel heat treated and subjected to... more

OTC FORD TRITON COMPRESSION ADPT 5.4L 4.6L

Features and Benefits: Works on 2004 and newer Ford 4.6 and 5.4 L 3 valve TritonT V-8 engines Easy to turn feature makes starting thread fast Use with compression testers with 14mm thread Patent pending Use with OTC compression testers (or other... more

OTC FUEL LINE DISCONNECT TOOL 3/8 1/2 FORD/GM DIESEL

Features and Benefits: Special low-profile design works in close quarters Designed to access the center port on GM fuel tank sending unit For 3/8 and 1/2 applications; will also service 2001 thru current 3/4- and 1-ton trucks with the Duramax Diesel... more

OTC 8-Piece Oxygen Sensor Socket Set

Features and Benefits: Kits includes: OTC4673-1: 29 mm (1-3/16 ) Vacuum Switch and O2 Socket 1/2 Drive OTC4673-2: 22mm (7/8 ) Vacuum Switch and O2 Socket (wide slot) 3/8 Drive OTC4673-3: 27 mm (1 1/16 ) Thermal Sensor Switch 1/2 Drive OTC4673-4: 22mm... more

OTC SMALL CONICAL PITMAN ARM PULLER XXX

Features and Benefits Conical Pitman Arm Puller designed for strength Large 3/4-16 X 4-3/4 forcing screw for power Designed to fit pitman ares on smaller cars Larger forcing screw for more power and strength Designed to pull stubborn pitman arms 3/4-16... more

OTC PULLER 2 JAW REVERSIBLE 4IN. 2 TON

Features and Benefits: This 2 jaw puller features a 2 ton pulling capacity Features reversible jaws Screw size 3/8 - 24 x 4-7/8 Maximum reach of 3-1/4 and with a maximum spread of 4 The jaw thickness: upper 3/16 lower 1/8 ; and the jaw width: upper 1/4... more

OTC A/C CLUTCH PULLER PULLER SET

Features and Benefits: Two pair of jaws Spread: 3 to 5 Reach: 1 to 5 One 3/4 -16 x 5 live center forcing screw A clamp bolt 5-1/2 crossbar with 3 spread settings Weight: 4 lbs ; 11oz This is used for the removal of stubborn air conditioning clutch... more

2-3/4 Hub Locknut Socket Wrench

Features and Benefits: Can be used with a 1/2 square drive extension and/or torque wrenchFor use on 1985 and newer Ford F-series 3/4 and 1 ton truck with Dana 80 rear axles.Made from high strength steel designed to resist rounding outSame as... more

OTC Gear & Pulley Puller

Features and Benefits: Perfect for removing timing gears fan pulleys harmonic balancers and many other parts having tapped holes. Puller Spread: 1-1/2 to 4-1/4 Puller blocks are 4-7/8 wide Includes two hex head cap screws 3/8 - 16 x 3 long. 13 long... more

OTC Tools & Equipment 1545 Stinger Motocycle Lift

1 500 lb. capacity and 17 in. long skids that will liftthe largest widest cruisers Lowest clearance available 3-1/2 in. at lowest level with a wide lift range of 3-1/2 in. to 16-3/4 in Removable handle provides 360 degrees access to load Features also... more

OTC TIE ROD ADJUSTING TOOL XXX

Features and Benefits: Adjusts tie rods on heavy duty Ford 3/4 ton and 1 ton trucks 1-13/16 diameter adjusting sleeves Permits 360 degree rotation more

OTC PULLER 2 JAW REVERSIBLE 6IN. 5 TON

Features and Benefits: This 2 jaw puller has a 5 ton capacity Features reversible jaws Maximum reach: 5-1/2 Maximum spread: 6 Screw size 9/16 - 20 x 6-15/16 Jaw thickness: upper - 5/16 and lower - 1/4 ; Jaw width: upper - 3/8 and lower - 3/4 This... more

OTC Brass Hammer and Punch Set

Features and Benefits: Brass-head hammer and punches are ideal to use where sparks from ferrous metals would be hazardous Hammer head weighs 24 oz.; brass drift punch is 10 x 3/4 diameter; brass tapered punch is 8 x 5/8 hex tapered to 3/8 diameter... more

OTC PULLER SLIDE HAMMER PILOT BEARINGS 1/2 TO 2IN.

Features and Benefits: Built especially for inside pulling jobs and particularly for removing flywheel pilot bearings on automobiles trucks and tractors Also very practical for pulling motor generator and magnet bearings Reach: 1-3/4 ; ID spread... more

BALL JOINT SPANNER WRENCH 1 DRIVE

Features and Benefits: Tool permits easy torquing with 1 socket for proper upper ball-joint preload Weight: 8 oz Designed for removal and installation of ball joint adjusting sleeves on 1/2 3/4 and 1 ton Dana open yoke front axles found on Ford GM... more

OTC Double Flaring Tool Set with Cutter

Features and Benefits: Designed for steel brake lines where double flaring is required Also performs 45 degree single flares on 3/16 1/4 3/8 7/16 1/2 and 5/8 copper aluminum brass and magnesium tubing Includes the tubing cutter and adapters for double... more

3-13/16 8-Point Wheel Bearing Locknut Socket

Features and Benefits: This high grade truck wheel bearing locknut is made of high strength steel Socket is designed for use with 3/4 square-drive manual tool only Opening size: 3-13/16 A long extension may be attached to the socket to provide the... more

BEARING SPLITTER 1/2 TO 5-3/4IN.

Features and Benefits: Minimum spread of 1/2 and a maximum spread of 5-3/4 Use with puller Nos. 1035 1040 1041 1042 1065 1063 and 938 Weight: 12 lbs. 5/8 - 18 thread of tapped hole in adapter 6 distance between adjusting screws These versatile... more

Gm/Chrysler Harmonic Balancer Puller

Features and Benefits: Easily removes damper pulleys Fits into tight engine compartments no need to remove radiator 3/8 drive for use with ratchet 3/4 drive for wrench or socket use Updated and expanded coverage of the popular OTC6267 Designed for... more

Small Universal Gland Nut Wrench

Features and Benefits: This wrench is fully adjustable to fit hydraulic cylinders on vehicles having gland nuts from 1 to 3-3/4 in diameter Also reverses to work on either 1/4 or 7/32 pinholes Accommodates a 1/2 drive ratchet Use w/ a 1/2 square drive... more

Oil Pressure Adapter

Features and Benefits:Allows for engine oil pressure to be measured.Installs in place of oil filter providing ports to attach oil pressure tester.Dual port for bottom or side tester connection.Installs with 11/16� (17mm) hex drive socket.Fits GM 4.8L... more

Harmonic Balancer Puller/Installer Set

Features and Benefits: For easy removal of most harmonic balancers and drive pulleys which are pressed fitted onto the crank shaft A bearing-centered circular 2/3-way and an assortment of metric and fractional bolts and adapters provide wide coverage A... more

DIFFERENTIAL BEARING PRELOAD TOOL

Features and Benefits: Similar to Miller C-4164 Tool fits inside axle tube to access the threaded adjusters Use to adjust differential bearing free play on Chrysler/Dodge vehicles with 7-1/4 8-1/4 8-3/4 and 9-1/4 rear axles. Lifetime Warranty Made in... more

Pilot Bearing Pulling Attachment

Features and Benefits: Use to pull a pilot bearing from the end of the crankshaft interchangeable jaws One set of jaws covers a spread of 1/2 to 1-1/2 ; other set of jaws covers a spread of 3/8 to 1-3/8 Reach has a min/max range of 3/16 to 1-1/4 Puller... more

POWER STEERING PUMP REMOVER

Features and Benefits: Reversible 2-in-1 tool removes and installs press-fit alternator and power steering pump pulleys Also removes and installs other press-fit pulleys Hub diameter of 1-1/8 (28mm) 1-1/4 (32mm) 1-5/16 (34mm) or 1-3/8 (35mm) Reversible... more

Hand/Foot Operated Air/Hydraulic Pump

Features and Benefits: Ideal all-around power source develops 10 000 PSI at 100 PSI air. 2-stage release mechanism; internal relief valve. Pump hold or release load with pedal control. 98 cu. in. of useable oil. 1/4 NPT Air Inlet. 3/8 NPT oil port. Not... more